Cisco 1000 Series
Product Overview
There are currently four Cisco 1000 series models:
- Cisco 1003 ISDN router
- One 10BaseT Ethernet port (RJ-45)
- One ISDN BRI WAN port (RJ-45)
- One console port (RJ-45)
- One Type-2 PCMCIA slot for Flash ROM card
- Cisco 1004 ISDN router
- One 10BaseT Ethernet port (RJ-45)
- One ISDN BRI WAN port (RJ-45), with an integrated NT1 device
- One console port (RJ-45)
- One Type-2 PCMCIA slot for Flash ROM card
- Cisco 1005 serial router
- One 10BaseT Ethernet port (RJ-45)
- One serial WAN port (DB-60) that supports asynchronous serial communications up to 115.2 kbps (EIA/TIA-232 interface) and synchronous serial such as leased lines, Frame Relay, switched 56 kbps, SMDS, and X.25 up to 2.048 Mbps (EIA/TIA-232, EIA/TIA-449, V.35, X.21, and EIA-530)
- One console port (RJ-45)
- One Type-2 PCMCIA slot for Flash ROM card
Cisco 1003 and Cisco 1004 ISDN Routers
The main difference between the two routers is that the Cisco 1004 router includes an integrated network termination 1 (NT1) device and the Cisco 1003 router does not. The ISDN service provider supplies the NT1 connection worldwide, except in North America, where the NT1 device is supplied by the customer. Therefore, the Cisco 1004 router is for use in North America, and the Cisco 1003 router is applicable worldwide.
The rear view of the routers looks the same except for the following differences, shown in the following figure:
- The BRI port on the Cisco 1003 is labeled "ISDN S/T," and "Cisco 1003" is stamped on the upper left corner of the chassis (not illustrated).
- The BRI port on the Cisco 1004 is labeled "ISDN U," and "Cisco 1004" is stamped on the upper left corner of the chassis (not illustrated).
Figure 7-173: Cisco 1003 and Cisco 1004 Rear View
| Characteristic | Description |
|---|---|
| Supported network interfaces | ISDN BRI (RJ-45)1
Ethernet 10BaseT (RJ-45) Console port (RJ-45) (EIA/TIA-232) |
| Processor type | Motorola 68360 |
| Software | IP, IPX, AppleTalk routing and bridging over ISDN. |
| Dimensions (H x W x D) | 1.75 x 8.0 x 8.3 in. (4.4 x 21 x 20.3 cm) |
| Weight | 6.0 lb (2.7 kg) shipping weight |
1 The ISDN BRI port is labeled "ISDN S/T" on the Cisco 1003 router and "ISDN U" on the Cisco 1004 router. The Cisco 1004 router includes an integrated NT1 device.
| Description | Specification |
|---|---|
| Power | Cisco 1003 and Cisco 1004: 12 VDC output, minimum 0.5A
Desktop external power supply: 100 to 240 VAC at 50 to 60 Hz, 1.0A input Wall-mount external power supply: 120 VAC at 60 Hz input (for Cisco 1004 routers used in North America only) |
| Operating temperature range | 32 to 104×F (0 to 40×C) |
| Nonoperating temperature range | -40 to 185×F (-40 to 85×C) |
| Operating humidity (noncondensing) | 10 to 90% |
Standard Features
The Cisco 1003 and Cisco 1004 routers include the following standard features:
- One Ethernet 10BaseT port with an RJ-45 connector
- One ISDN BRI port with an RJ-45 connector (the Cisco 1004 router includes an integrated NT1 device)
- One console port with an RJ-45 connector
- Console cable kit and power supply
- One external PCMCIA slot for optional Type-2 Flash memory card
- Software booting over an Ethernet LAN using TFTP
- Optional Flash memory card to store software image and configuration files, allowing network-independent booting and software updates over the WAN or LAN connections
- LAN-to-LAN DDR routing over ISDN lines
- IP, IPX, and AppleTalk routing
- Transparent bridging
- IPX and SPX spoofing
- PPP compression and bandwidth-on-demand with load balancing for throughput up to 512 kbps
- HDLC and standards-based PPP
- Increased security with CHAP, PAP, packet filters, local password, and CLI/ANI
- Network management and monitoring through the console port or over the network using SNMP or Telnet
Hardware
The following table lists the hardware product numbers for the Cisco 1003 and Cisco 1004 routers. If a product number ends with an equal sign (=), the item can be ordered only as a spare. If a product number does not end with an equal sign, the item can be ordered as a spare or as a configurable part of a system order.
| Option | Product Number |
|---|---|
| Base System | |
| Cisco 1003 Ethernet/ISDN BRI router | CISCO1003 |
| Cisco 1004 Ethernet/ISDN BRI router with NT1 | CISCO1004 |
| Options | |
| Console cable | CAB-1000-CON= |
| AC power supply | PWR-1000-AC1= |
| 4-MB to 8-MB DRAM upgrade | MEM-1003-8MD (Cisco 1003) MEM-1004-8MD (Cisco 1004) |
| 8-MB DRAM SIMM | MEM-1000-8MD= |
Software
Refer to the "Cisco Internetwork Operating System (IOS) Software" chapter for detailed software feature set information.
Cisco 1005 Serial Router
The Cisco 1005 router is a small, desktop router that connects small, remote sites with Ethernet LANs to synchronous WANs at speeds up to 2.048 Mbps or to asynchronous WANs at speeds up to 115.2 kbps.
Figure 7-174: Cisco 1005 Rear View
| Characteristic | Description |
|---|---|
| Supported network interfaces | Serial port (DB-60)1
Ethernet 10BaseT (RJ-45) Console port (RJ-45) (EIA/TIA-232) |
| Processor type | MC68360 |
| Software | IP, IPX, AppleTalk routing and bridging over leased lines, Frame Relay, Switched 56, SMDS, and X.25. IP/IPX routing over asynchronous WAN links. |
| Dimensions (H x W x D) | 1.75 x 8.0 x 8.3 in. (4.4 x 21 x 20.3 cm) |
| Weight (average shipping) | 6.0 lb (2.7 kg) |
1 The serial port supports asynchronous communications through an EIA/TIA-232 interface and synchronous communications through the following interfaces: EIA/TIA-232, EIA/TIA-449, V.35, X.21, and EIA-530.
| Description | Specification |
|---|---|
| Power | 12 VDC output, minimum 0.5A
External power supply: 100 to 240 VAC at 50 to 60 Hz, 1.0A input |
| Operating temperature range | 32 to 104×F (0 to 40×C) |
| Nonoperating temperature range | -40 to 185×F (-40 to 85×C) |
| Operating humidity (noncondensing) | 10 to 90% |
Standard Features
The Cisco 1005 router includes the following features:
- One Ethernet 10BaseT port (RJ-45)
- One console port (RJ-45)
- Console cable kit and power supply
- One serial port (DB-60) that supports permanent and switched synchronous WAN links up to 2.048 Mbps and asynchronous WAN links up to 115.2 kbps
- One slot for an optional PCMCIA Flash memory card
- Software boot using TFTP over an Ethernet LAN connection or by using the optional Flash memory card
- IP, IPX, and AppleTalk routing
- Transparent bridging (over synchronous WAN links only)
- Support for the following synchronous WAN encapsulations: HDLC, LAPB, Frame Relay, SMDS, and X.25
- Support for the following asynchronous WAN encapsulations: PPP and SLIP
- Router management through the console port or over the network using SNMP or Telnet
- AutoInstall for downloading configuration files automatically over a WAN
Hardware
The following table lists the hardware product numbers for the Cisco 1005. If a product number ends with an equal sign (=), the item can be ordered only as a spare. If a product number does not end with an equal sign, the item can be ordered as a spare or as a configurable part of a system order.
| Option | Product Number |
|---|---|
| Base System | |
| Cisco 1005 Ethernet/synchronous serial router | CISCO1005 |
| Options | |
| Console cable | CAB-1000-CON= |
| AC power supply | PWR-1000-AC1= |
| EIA/TIA-232 male DTE interface, 10 ft (3 m) | CAB-232MT |
| EIA/TIA-449 male DTE interface, 10 ft (3 m) | CAB-449MT |
| EIA-530 male DTE interface, 10 ft (3 m) | CAB-530MT |
| V.35 male DTE interface, 10 ft (3 m) | CAB-V35MT |
| X.21 male DTE interface, 10 ft (3 m) | CAB-X21MT |
| 4-MB to 8-MB DRAM upgrade | MEM-1005-8MD |
| 8-MB DRAM SIMM | MEM-1000-8MD= |
Software
Refer to the "Cisco Internetwork Operating System (IOS) Software" chapter for detailed software feature set information.
I want some more information!
Back to the Cisco Products page